2K-Deripox Grund 60 HS

Technical Specification
2K-Deripox Grund 60 HS

Colours	redbrown, light-grey.
Flash point	>23 °C
Temperature stability	-20 up to 200 °C
Gloss	Mat
Potential dry film thickness in one working process	50 up to 100 µm
Mixing ratio	Hardener HL 500
(Basis:hardener) by weight	10:1
(Basis:hardener) by volume	5,7:1
Pot life in hours	8
Viscosity	Appr. 17 sec running time (DIN 6 mm pot)
Density in kg/l	1,56
Solid content in %	75
Solid volume in %	56
Theoretical spreading capacity	11,2 m²/l at 50 µm DFT 7,18 m²/kg at 50 µm DFT
Recommended film thickness	100 µm WFT corresponds to 60 µm DFT
Drying (DIN EN ISO 1517)	50 µm DFT
Dust-dry (Tg1)	After 25 min
Touch-dry (Tg4)	After 2 h
Dry (Tg6)	After 6 h
Cured chemically	After 7 days
Interval for overcoating	after 5 h with two component Deripox topcoats Max. after 6 months without slightly sanding after 6 h with two component Derocryl topcoats

Note

• The specifications are related to the prepared mixture and are based on standard atmospheric conditions 23/50, DIN 50014.
• Lower temperatures and/or higher humidity will prolong drying and hardening.
• Application below +5 °C is not possible.

Safety information
2K-Deripox Grund 60 HS

(See Security Data Sheet)

VOC-level	Appr. 380 g/l
Solvent content	Appr. 25 % by weight
Aromatic content	Appr. 19 % by weight

Storage
2K-Deripox Grund 60 HS

Storage

• In dry, cool rooms, if possible frost-proof
• Ensure good ventilation

Shelf life

• 6 month from date of delivery when in unopened original containers in cool and dry conditions

Application methods
2K-Deripox Grund 60 HS

Mixing ratio

• Stirr homogeneous, preferably with mechanical stirrer
• Mix base paint and hardener according to the mixing ratio as specified

Airless spraying

• Flow pressure 160 bar
• Nozzle size 0,011 inch (0,28 mm)
• Spraying angle according to the geometry and size of the object to be laquered

Compressed air spraying

• Spraying pressure 4 - 6 bar
• Nozzle size 1,5 - 2 mm
• Adjust to spraying viscosity (appr. 30 s DIN 4 mm) adding appr. 8 % Deripox-Verdünnung (two component products: after mixing)

Electrostatic application

• Can be applied as delivered
• Conductance of the material: 1000 kΩ

Dipping

• Can not be applied as delivered

Other methods

• Roller and brush application is possible in the quality as delivered
• Double application is possible in viscosity as delivered

Thinner

• Max. 10% Deripox-Verdünnung

Cleaning

• Rinse immediately with Deripox-Verdünnung

Preparation of support

• Shot blasting to a purity according to SA 2½
• If necessary clean with high pressure-cleaner and turbo-cleaner-solution
• Sweeping for zinced supports
• Mill scale, welding residues, dust, soluble residues from chemical pretreatments and zinc reaction products which might reduce adhesion have to be carefully and thoroughly removed

General remarks

• During coating and drying the humidity should be min. 10 % / max. 85 %
• During coating and drying the environmental temperature should be min. 5°C / max. 30°C
• Object temperature at least 3° C above dew point.

Example for a system

• Primer coat: 2K-Deripox Grund 60 HS
• Finish coat: